Temperaturspezifisches Wachs für Ski und Snowboards. 85 g Grün -15 bis -5°C WINTERSTEIGER Slik Wax Temperature specific wax for skis and snowboards Clean base with wax remover and allow base cleaner to completely evaporate (up to 30 minutes). Set wax iron to correct temperature setting so the wax will melt but not smoke. With the wax bar on the sole of the iron drip the wax down the length of the ski or snowboard, not allowing the iron to contact the base. Now use the iron to melt the wax and completely cover the base, drip on more wax if needed. Pass the iron from tip to tail at a steady speed which is slow enough to leave a trail of melted wax about 3 inches long. Don’t over heat the ski, you should not be able to feel heat on the top skin. Allow to cool completely and remove excess wax from the base ...

Temperaturspezifisches Wachs für Ski und Snowboards. 85 g blue -12 bis -8°C WINTERSTEIGER Slik Wax Temperature specific wax for skis and snowboards Clean base with wax remover and allow base cleaner to completely evaporate (up to 30 minutes). Set wax iron to correct temperature setting so the wax will melt but not smoke. With the wax bar on the sole of the iron drip the wax down the length of the ski or snowboard, not allowing the iron to contact the base. Now use the iron to melt the wax and completely cover the base, drip on more wax if needed. Pass the iron from tip to tail at a steady speed which is slow enough to leave a trail of melted wax about 3 inches long. Don’t over heat the ski, you should not be able to feel heat on the top skin. Allow to cool completely and remove excess wax from the ...

Temperaturspezifisches Wachs für Ski und Snowboards. 85 g blue -12 bis -8°C WINTERSTEIGER Slik Wax Temperature specific wax for skis and snowboards Clean base with wax remover and allow base cleaner to completely evaporate (up to 30 minutes). Set wax iron to correct temperature setting so the wax will melt but not smoke. With the wax bar on the sole of the iron drip the wax down the length of the ski or snowboard, not allowing the iron to contact the base. Now use the iron to melt the wax and completely cover the base, drip on more wax if needed. Pass the iron from tip to tail at a steady speed which is slow enough to leave a trail of melted wax about 3 inches long. Don’t over heat the ski, you should not be able to feel heat on the top skin. Allow to cool completely and remove excess wax from the ...

Temperaturspezifisches Wachs für Ski und Snowboards. 85 g yello  +4°C and warmer WINTERSTEIGER Slik Wax Temperature specific wax for skis and snowboards Clean base with wax remover and allow base cleaner to completely evaporate (up to 30 minutes). Set wax iron to correct temperature setting so the wax will melt but not smoke. With the wax bar on the sole of the iron drip the wax down the length of the ski or snowboard, not allowing the iron to contact the base. Now use the iron to melt the wax and completely cover the base, drip on more wax if needed. Pass the iron from tip to tail at a steady speed which is slow enough to leave a trail of melted wax about 3 inches long. Don’t over heat the ski, you should not be able to feel heat on the top skin. Allow to cool completely and remove excess wax ...

Plexi Scraper 3mm / 5mm To remove cooled wax from the base After the wax has cooled to room temperature, any excess must be scraped off and the structure must be brushed. Always allow the wax and the ski or snowboard to cool to room temperature before scraping, otherwise the warm wax will be pulled from the pores, leaving the base dry. Start by using a plastic scraper with a 90° edge at a slight angle. Beginning with the tip of the ski or snowboard and using long overlapping strokes, start removing excess wax from the base. Repeat until all of the wax is removed from the base. Make sure any wax that may have dripped down the sidewalls is removed as well. After the wax is scraped from the base it should then be brushed for optimal performance.

Plexi Scraper  5mm To remove cooled wax from the base After the wax has cooled to room temperature, any excess must be scraped off and the structure must be brushed. Always allow the wax and the ski or snowboard to cool to room temperature before scraping, otherwise the warm wax will be pulled from the pores, leaving the base dry. Start by using a plastic scraper with a 90° edge at a slight angle. Beginning with the tip of the ski or snowboard and using long overlapping strokes, start removing excess wax from the base. Repeat until all of the wax is removed from the base. Make sure any wax that may have dripped down the sidewalls is removed as well. After the wax is scraped from the base it should then be brushed for optimal performance.

Plexi Scraper 3mm / 5mm To remove cooled wax from the base After the wax has cooled to room temperature, any excess must be scraped off and the structure must be brushed. Always allow the wax and the ski or snowboard to cool to room temperature before scraping, otherwise the warm wax will be pulled from the pores, leaving the base dry. Start by using a plastic scraper with a 90° edge at a slight angle. Beginning with the tip of the ski or snowboard and using long overlapping strokes, start removing excess wax from the base. Repeat until all of the wax is removed from the base. Make sure any wax that may have dripped down the sidewalls is removed as well. After the wax is scraped from the base it should then be brushed for optimal performance.

Die perfekte Allround Bindung kombiniert mit leichtem Gewicht. Mit einer DIN Zahl bis 10 kann diese Bindung auf jeden Ski ohne integriertes System montiert werden.       SL Ferse   SL Backen mit TRP System   Full Diagonal   Dura-Beschichtung  

 Colour Red/Black/Silver

Modell 08/09   Der extrem leichte Airshock Protektor bietet bestmöglichen Schutz bei optimaler Bewegungsfreiheit! Die Sandwichbauweise des Protektors besteht aus einem Kern von expandierendem Polysterol (EPS), der trotz ultimativ geringem Gewicht eine optimale Absorption der auftreffenden Energie garantiert. Die Funktion kann mit der Knautschzone beim Auto verglichen werden.   kein Verrutschen der Protektoren durch einfache Fixierung mittels Schlaufe & Knopf   features: -   CE-geprüfter, superleichter Airshock Protektoreneinsatz, gute Passform -   anatomisch geformtes Rückenteil im modernen Design -   neues Gurtsystem für optimale Passform, einfach anzuziehen wie ein Rucksack -   elatischer Nierengurt mit Klettverschluss   sizes:  XS- L ...