Sturdy, high-tensile aluminum vise for tuning all types and shapes of skis Secure the vise to a sturdy table or solid work surface. The supports should be spaced so they provide support while not allowing the ski to over flex. Using the supplied brake retainers, secure the brakes in the up position. Place the ski on the supports and center it from side to side. For additional security, clamp the smaller black clamp to your bench or work surface under the toepiece. Place the rubber triangle around the toe piece and hook to the clamp. For working on the side edge, lift and turn the ski 90 degrees, keeping the base away from you, and place into the center jaws.

High quality wax iron for skis and snowboards Instructions of Use Connect the appliance to compatible voltage as indicated on the name plate (110V). As with any appliance, never leave unattended while plugged into the power supply and unplug when not in use. Do not use near flammable products. Keep out of reach of small children and pets. Do not attempt to make any repairs or modifications to the appliance. For repairs during the warranty period, return the appliance to the retailer where it was purchased. THIS APPLIANCE IS DESIGNED EXCLUSIVELY TO WAX SKIS AND SNOWBOARDS. ALL CLAIMS FOR DAMAGE RESULTING FROM OTHER USES WILL BE DENIED. Temperature Settings The correct temperature setting depends on many factors, including the type of wax, ambient temperature of the room and base. The temperature setting is correct when no ...

Edge sharpener including Trizact, File and Diamond Tools The EASY SHARP is available with 3 different tools for easy maintenance of side edges. The TRIZACT tool is used to clean rusty edges while removing rock burrs. The FILE sharpens and bevels the edges while removing damaged areas. The DIAMOND is used to finish the edge, removing the small burr formed during filing, and leaving the edge smooth and sharp. Make sure your tools are clean before you start, and replace any that have become worn and dull. The TRIZACT and DIAMOND tools are multidirectional and can be placed in the holder any way. The FILE is directional and can only be used in the direction of the arrow. Choose the proper angle and use the TRIZACT tool first. Make long overlapping strokes until all rust is removed. Next, insert the file and use the same method ...

Edge sharpener including Trizact, File and Diamond Tools The QUICK SHARP is available with 3 different tools for easy maintenance of your side edges. The TRIZACT tool is used to clean rusty edges while removing rock burrs. The FILE sharpens and bevels the edges while removing damaged areas. The DIAMOND is used for finishing the edge, removing the small burr formed during filing, and leaving the edge smooth and sharp. Make sure your tools are clean before you start, and replace any that have become worn and dull. The TRIZACT and DIAMOND tools are multidirectional and can be placed in the holder any way. The FILE is directional and can only be used in the direction of the arrow. Choose the proper angle and use the TRIZACT tool first. Make long overlapping strokes until all rust is removed. Next, insert the file and use the ...

Citrus Base Cleaner For removing grease, adhesives and for cleaning The best Citrus Cleaner available on the market today! The organic extract used in this formulation makes this base cleaner very easy to use. Use as a replacement for dangerous chlorinated hydrocarbon solvents. This product is non-corrosive and contains petroleum and fruit distillates. Use full strength for removing grease, adhesives and cleaning. Cleaning the Ski/Board: Always take the time before tuning to clean both the top sheet and base. Use a cloth with a small amount of base cleaner to remove dirt and built-up debris from the sides and top sheet. Don’t forget to clean the ski/board again after the tune up to remove any built-up wax from the sidewalls and edges. Make sure to avoid getting base Cleaner on the base once the tune is complete. Using base ...

Plexi Scraper 3mm / 5mm To remove cooled wax from the base After the wax has cooled to room temperature, any excess must be scraped off and the structure must be brushed. Always allow the wax and the ski or snowboard to cool to room temperature before scraping, otherwise the warm wax will be pulled from the pores, leaving the base dry. Start by using a plastic scraper with a 90° edge at a slight angle. Beginning with the tip of the ski or snowboard and using long overlapping strokes, start removing excess wax from the base. Repeat until all of the wax is removed from the base. Make sure any wax that may have dripped down the sidewalls is removed as well. After the wax is scraped from the base it should then be brushed for optimal performance.

Plexi Scraper  5mm To remove cooled wax from the base After the wax has cooled to room temperature, any excess must be scraped off and the structure must be brushed. Always allow the wax and the ski or snowboard to cool to room temperature before scraping, otherwise the warm wax will be pulled from the pores, leaving the base dry. Start by using a plastic scraper with a 90° edge at a slight angle. Beginning with the tip of the ski or snowboard and using long overlapping strokes, start removing excess wax from the base. Repeat until all of the wax is removed from the base. Make sure any wax that may have dripped down the sidewalls is removed as well. After the wax is scraped from the base it should then be brushed for optimal performance.

Temperaturspezifisches Wachs für Ski und Snowboards. 85 g Grün -15 bis -5°C WINTERSTEIGER Slik Wax Temperature specific wax for skis and snowboards Clean base with wax remover and allow base cleaner to completely evaporate (up to 30 minutes). Set wax iron to correct temperature setting so the wax will melt but not smoke. With the wax bar on the sole of the iron drip the wax down the length of the ski or snowboard, not allowing the iron to contact the base. Now use the iron to melt the wax and completely cover the base, drip on more wax if needed. Pass the iron from tip to tail at a steady speed which is slow enough to leave a trail of melted wax about 3 inches long. Don’t over heat the ski, you should not be able to feel heat on the top skin. Allow to cool completely and remove excess wax from the base ...

Temperaturspezifisches Wachs für Ski und Snowboards. 85 g blue -12 bis -8°C WINTERSTEIGER Slik Wax Temperature specific wax for skis and snowboards Clean base with wax remover and allow base cleaner to completely evaporate (up to 30 minutes). Set wax iron to correct temperature setting so the wax will melt but not smoke. With the wax bar on the sole of the iron drip the wax down the length of the ski or snowboard, not allowing the iron to contact the base. Now use the iron to melt the wax and completely cover the base, drip on more wax if needed. Pass the iron from tip to tail at a steady speed which is slow enough to leave a trail of melted wax about 3 inches long. Don’t over heat the ski, you should not be able to feel heat on the top skin. Allow to cool completely and remove excess wax from the ...

Temperaturspezifisches Wachs für Ski und Snowboards. 85 g blue -12 bis -8°C WINTERSTEIGER Slik Wax Temperature specific wax for skis and snowboards Clean base with wax remover and allow base cleaner to completely evaporate (up to 30 minutes). Set wax iron to correct temperature setting so the wax will melt but not smoke. With the wax bar on the sole of the iron drip the wax down the length of the ski or snowboard, not allowing the iron to contact the base. Now use the iron to melt the wax and completely cover the base, drip on more wax if needed. Pass the iron from tip to tail at a steady speed which is slow enough to leave a trail of melted wax about 3 inches long. Don’t over heat the ski, you should not be able to feel heat on the top skin. Allow to cool completely and remove excess wax from the ...

Temperaturspezifisches Wachs für Ski und Snowboards. 85 g yello  +4°C and warmer WINTERSTEIGER Slik Wax Temperature specific wax for skis and snowboards Clean base with wax remover and allow base cleaner to completely evaporate (up to 30 minutes). Set wax iron to correct temperature setting so the wax will melt but not smoke. With the wax bar on the sole of the iron drip the wax down the length of the ski or snowboard, not allowing the iron to contact the base. Now use the iron to melt the wax and completely cover the base, drip on more wax if needed. Pass the iron from tip to tail at a steady speed which is slow enough to leave a trail of melted wax about 3 inches long. Don’t over heat the ski, you should not be able to feel heat on the top skin. Allow to cool completely and remove excess wax ...

For fine buffing and polishing on the edge Used for finer buffing and polishing on a ski and snowboard edge. Dimensions: 2 1/2“ x 1 1/2“ x 3/4“ (6,5 x 3,8 x 1,9 cm) Starting at the tip of the ski/board, the gummi stone should be run at a 45 degree angle for up to 4” to 8” (10 to 20 cm) past the contact point. Making multiple passes, reducing the length of the stroke each time, feather the edge from the tip to the set bevels. Run the gummi stone from tip to tail to deburr and repeat the detune process in the tail. The further down the ski/board the detune is applied the more forgiving the ski/board becomes. This allows for smoother initiation and easier release of the turn. The shorter the detune the more aggressive the ski/board becomes. The more the edges are detuned the less effective the side cut is on the ...