Finally a small engine with the same quality of the engines of machines that cost over 3500 euros.   Until now, buyers of retrofit stringing motors have always had to compromise on quality. In other words, there was a clear difference to the expensive high-tech machines on the market.   This new, accurate, high-quality, processor-controlled stringing motor puts an end to that. You can now upgrade your lever or crank machine with this professional motor and enjoy a motor of the highest quality.   The engine has a chain hoist system. Usually only the very expensive machines have 4000,- Euro upwards. = When buying the engine, make sure that the motor has a chain hoist system.   Incl. knot function!   Incl. glide to activate = when you move the jaws of the quick release, ...

Motor for stringing machines. Pulling system with a chain (most of the expensive machines have a motor with a chain pulling system) Continuous pull Tension can be set in pounds or kilos Digital readout Speed control - 3 speed settings New quieter motor Touch pad  Pre-stretch function to varying percentages Memory banks Knot function Glide to activate You find the video under the media button  or on youtube  

The new 2086  (v14) = Version 14 incl. Knot function! Professional Tension Head is designed to convert your existing manual pull machine to a modern constant pull stringing machine. It takes only minutes to simply remove your manual tension head and clamp on the electronic head Accuracy to a tenth of a pound Continuous pull or lock out tensioning Tension can be set in pounds or kilos Digital readout Speed control - 3 speed settings New quieter motor Touch pad stringing or a foot control is available as an optional extra Pre-stretch function to varying percentages Memory banks and other time savers Knot function NEW - Knot Function. You can use the pause button for knot function       For speed, accuracy and reliability the 2086 Professional Tension Head is the ...

New string gripper system with glide to activate: https://youtu.be/fGBUrRXSe6Q Fit only for V14 version of the wise tennsionhead.    Attention: If you change the original wise string gripper system you should know that this string gripper system is higher (about 25 mm) then the original.   = you should raise the turntable about 25 mm (2,5 cm).   You can use washers for this or this distance tubes:   distance tubes

New string gripper system with glide to activate: https://youtu.be/fGBUrRXSe6Q   For wise tensionhead version 12   incl. distance tubes (2,5 cm) for raising the turntable of the machine

 This Gripper, replaces any of the models of the WISE 2086 series. gripper switch is included. -Made of high precision machined soft aluminum minimizes the damage to the string. -Unique design with roller bearings allows for a better pressure distribution Maintenance: remove from machine. Clean with acetone as needed. Lubricate periodically with 2 drops of 3 in 1 sewing oil on each side of the roller jaws.Keep oil from dripping inside the machine. Replace if jaws are worn out or  show signs of  uneven wear..      

Calibrator The 2090 is a sophisticated tool for measuring the accuracy of your tension head. It can be used on any stringing machine, electronic or manual. It displays in kilos or pounds and shuts itself off when it is not in use for more than 1 minute.     CALIBRATOR DIRECTIONS Mount a racket on your machine. Cut a short length of string (even scrap will do). Pass the string through to the racket clamp furthest from the racket then loop it into one of the links in the 2090. Place the 2090 in the center of the not-strung racket. Use another small piece of string and pass it through the other link and to the open jaws of the gripper. This is done so the 2090 does not sag and present an inaccurate reading. Compare the 2090 reading to the setting on your machine. Adjust your machine if necessary. You can return the ...

  

"adapter (low hight) for the Wise 2086 Electronic Tennishead universal"  With this adapter you can fix your wise Motor on drop weight stringing machines:   Hight: 20,2 mm   This adapter fits to   Premium Stringer 3600 Premium Stringer 3800 Superstringer T10 Superstringer T12 Superstringer T15 Superstringer T20 Superstringer T70 Superstringer T80 TennisMan StringMaster Pro 46 und Pro 50 TennisMan StringMaster 3700, 3800 und 4000 TennisMan StringMaster Deluxe (und die Special Edition) Tyger StringEco 45 

Wise 2086 Gamma Adaptor Plate => to connect the wise motor to Gamma crank machines

  hight: 34,5mm

Wise 2086 High Height Adaptor Plate You can use this for mounting the wise tenstionhead motor on gamma progression II 602 FC  hight: 45 mm